Category: System Design & Installation

This article originally appeared in the Fire & Safety Journal Americas, Aug. 2026.

Fire protection systems are often judged at the moment they are commissioned. The final inspection is complete, the system passes its acceptance test, and the building is cleared for occupancy. Yet commissioning is only the beginning of a system’s operational life. Water based fire protection systems remain in place for decades, serving buildings that evolve, age, and change in ways designers cannot fully predict. The true measure of a system is not how it performs on day one, but how it performs on day 5,000.

Long term reliability is not a passive outcome. It is the result of deliberate design choices, informed installation practices, and consistent maintenance over time. As buildings become more complex and risk expectations increase, the fire protection industry must place greater emphasis on designing systems that remain serviceable, maintainable, and dependable throughout their life cycle.

A water based fire protection system is more than a collection of pipe, valves, drains, vents, and sprinklers. It is a long term safety asset. Like any asset, its performance depends not only on how it is designed and installed, but also on how well it can be inspected, tested, drained, vented, repaired, and returned to service over many years.

When it comes to fire protection, codes and standards provide the baseline: reliable systems designed to save lives and protect property. But for building owners, simply meeting minimum code requirements doesn’t always address the everyday challenges of operating and maintaining these systems. Increasingly, the fire protection industry is embracing technologies and product designs that go beyond compliance to deliver added value through convenience, cost savings, and peace of mind.

Building Codes: The Starting Point, Not the Finish Line

Codes are essential, but they’re written to ensure safety, not to optimize building operations. They don’t always account for factors like maintenance labor, service costs, or the risk of incidental water damage. Manufacturers and contractors are stepping in to fill that gap by offering products that streamline maintenance, reduce nuisance issues, and provide owners with tools for smarter management of their fire protection systems. For example, AGF’s Flood Eliminator is a product designed to allow condensate water to collect normally in a standard drum drip but then, if presented with the flow that would result from a failed drum drip, automatically trip to cut off that flow, eliminating the flooding and damage that would result from the system’s failure.

In multi-story buildings, floor control assemblies are essential for isolating, draining, and testing individual floors of a sprinkler system. However, finding space to install these assemblies, especially in tight stairwells or shared mechanical areas, can be a challenge. That’s where corner-mounted designs like the AGF Model 8611 Corner Riser offer a practical, code-conscious solution.

Whether used as a floor control assembly or a main riser, the 8611 is engineered to reduce obstructions, support accessibility, and simplify installation.

The Space Challenge in Stairwells and Corridors

Floor control assemblies are often installed in stairwells of hotels, apartment buildings, and high-rises. These spaces are highly trafficked, frequently narrow, and must remain clear for emergency egress. Flat wall-mounted assemblies can protrude significantly, posing hazards and potentially violating ADA and local building codes.

By mounting the assembly in a 90-degree corner, Model 8611 significantly reduces its profile, helping maintain safe, unobstructed walkways.

Alternatively, the corner riser can be mounted horizontally and tucked into the corner between the ceiling and wall. This offers a space-saving solution while being able to access the TESTanDRAIN handle for testing and the 7000L pressure relief valve. AGF’s three-way gauge valve has always been accessible since its redesign, which rotates the handle so it should never need to face the wall or ceiling while having the pressure gauge facing out.

When it comes to protecting fire sprinkler systems from over-pressurization, pressure relief valves are a key component. But for years, there’s been confusion about what the pressure rating on these valves actually means, especially when it comes to the opening and closing pressures.

With the release of the 2025 edition of NFPA 13, that confusion is finally being addressed. New language in the handbook offers long-awaited clarity, helping system designers, inspectors, and maintenance personnel better understand how relief valves are supposed to perform.

The 2025 edition of NFPA 13 finally adds clarity.

As building designs become more compact and mechanical spaces become more congested, fire protection systems must adapt to fit tighter footprints without sacrificing reliability or code compliance. AGF’s Model 8611 Corner Riser is designed with this challenge in mind—offering a smarter, more space-efficient solution for floor control assemblies.

Continue reading Save Space Without Compromising Performance: AGF’s Model 8611 Corner Riser →

AGF Manufacturing is a family-owned American manufacturer. It isn’t just a tagline—it’s a core part of who we are. 

For over 35 years, we’ve proudly engineered, manufactured, assembled, and shipped innovative fire sprinkler products all over the World, supporting American workers and delivering reliable solutions to contractors, engineers, and facility owners. Today, with growing emphasis on sourcing transparency and compliance with federal procurement rules, domestic manufacturing matters more than ever.

Navigating BABAA and Buy American Requirements

The Build America, Buy America Act (BABAA)—introduced as part of the 2021 Infrastructure Investment and Jobs Act—places stricter requirements on federally funded infrastructure projects. Specifically, BABAA mandates that all iron, steel, manufactured products, and construction materials used in these projects must be produced in the U.S.